Vinyl Record Inner-Groove Distortion (A Simple Explanation)

Marc HenshallTech Talk, Vinyl 10120 Comments

While vinyl records have plenty to offer, both sonically and from a listening experience standpoint, they also come with some trade-offs. One of the most commonly cited but also misunderstood trade-offs is a phenomenon known as inner-groove distortion (also referred to as end-of-side distortion.

Inner-groove distortion is an audible deterioration in sound quality that sometimes occurs when playing tracks close to the end of each side. Some would call it a design flaw, for others, it’s just part of the vinyl experience. But what causes it? Let’s dig (briefly) into some light physics…

inner-groove-distortion

The fundamental cause of inner-groove distortion is the progressive reduction of linear resolution as a record progresses. Put another way: there is more vinyl per second available at the large-diameter beginning of the record than exist at the smaller-diameter toward the end of each side. Subsequently, the wavelengths become gradually shorter and more compressed (like an accordion) as you get closer to the records centre. These more condensed grooves are much harder for the stylus to track accurately.

The problem is most noticeable at higher recorded volumes (particularly if there’s a lot of high-frequency energy). Mastering engineers will attempt to mitigate end-of-side distortion by pressing quieter songs, with moderate bass and lower HF energy towards the center of each side. Alternatively, they will restrict the playing time, or spread an album over two discs to avoid inner grooves.

Even when taking linear resolution into account, there is still the issue of cartridge and stylus alignment. The machines used to cut records operate on a parallel basis, meaning the cutting stylus is perfectly aligned from start to finish. Turntables, on the other hand, use a pivoting tonearm, which can only line up correctly at two points across the record surface (it’s a fact of geometry). A properly configured, high-quality turntable with a minimum 10inch tone arm can reduce tracking errors significantly, but tracking errors will always be most noticeable at the inner grooves – thus further encouraging end-of-side distortion.

Various attempts have been made to mitigate end-of-side distortion – such as purposefully misaligning the cartridge to improve inner-groove tracking at the expense of outer grooves, however, the fact remains it will always be a compromise.

With all of this in mind, it would be easy to dismiss vinyl as a flawed medium, which of course it is. But that doesn’t make vinyl any less relevant – far from it. In many cases, inherent distortion in the vinyl format is what draws people in; often referred to as “analog warmth,” what we’re actually experiencing is the analog medium imparting sonically pleasing distortion. The line at which pleasant, warming distortion becomes irritating distortion will be different for everyone, but some distortion is just part of the deal with vinyl.

The best course of action is to invest in a good turntable and ensure you configure it precisely. After all, if you play records on a poorly setup deck, the inner grooves will suffer the greatest damage.

How to Set up Your Turntable

There are many variables in turntable setup. For the purpose of this article, we’ll take a look at the fundamentals: tracking pressure, cartridge alignment, and anti-skating. By getting these set correctly, we can greatly reduce tracking errors, and ultimately, achieve better sounding records.

Tracking Pressure (downforce)

The counter weight on the end of your tonearm is used to apply the correct amount of pressure in agreement with the manufacturer’s recommendations. (Check your cartridge manual for the proper weight).

Here’s how to apply the weight specified:

1: Start by setting the turntable’s anti-skating dial to zero (you don’t want any additional weight on the tone arm at this stage).

2: Use the weight on the back of the arm to balance the tonearm until it floats on its own.

3: Turn the number dial (which turns independently from the weight itself) until it reads zero. The tonearm should still be floating freely, and you’re ready to apply the weight specified in your cartridge manual.

4: Turn your counter-weight until the dial reads the correct number. Once set, your cartridge will track at approximately the right pressure.

(Refer to your turntable manual for details on how your counterweight scale represents downforce. In my case, one mark on the scale represents 1 mN (0.1g). To apply the 1.75g required for my cartridge, I simply set the counterweight to 17.5 mN.)

5: To ensure a more accurate weight, adjust using a stylus tracking force gauge.

Cartridge Alignment

As determined earlier, the cartridge can only correctly align with the record grooves at two points across the record. It is critical we achieve correct alignment at these points to ensure minimal tracking errors across the remaining surface area. For this application, I recommend using a cartridge alignment protractor.

Step 1: If your headshell allows for overhang adjustment (that’s the distance between your center spindle and the stylus tip) make sure you adjust the length in agreement with your turntable manual. Mine specifies 22mm.

overhang-test

Step 2: Place your cartridge alignment protractor on the platter, and carefully drop the stylus tip onto the first alignment point. The metal cantilever holding the stylus tip should be parallel with the guidelines on your protractor – if it isn’t, carefully adjust the headshell screws and adjust until everything lines up. (The alignment tool I’ve linked comes with a mirror to help you achieve accurate results). You can also use the front and side of the cartridge body to help you achieve perfect alignment with the horizontal and vertical lines on your protractor.

Step 3: Use the second point to check your results. If all is well, the cartridge should align correctly at both points.

Anti-skate

Essentially, the purpose of anti-skate is to counteract the force naturally pulling your stylus toward the record spinal. This force encourages the stylus to rid the inner edge of record grooves and prevents it from sitting centrally. The result is decreased sound quality and increased record wear.

The best way to test anti-skate is using a test record, which will have a blank groove purposely intended for setting anti-skate. When the correct weight is applied, your stylus will sit centrally in the blank space without rocking or riding toward the center spindle.

The following video below is one of the clearest explanations of anti-skate I’ve stumbled across on the web:

Final adjustments: Vertical Tracking Angle (VTA) & Azimuth

With the above adjustments made, the final adjustments you want to check are Azimuth and vertical tracking angle.

First up, azimuth refers to the how the cartridge is aligned from a horizontal perspective. When the azimuth is set correctly, your cartridge is 100% level over the record grooves. In other words, the cartridge isn’t tilted left or right and hovers evenly over the record surface.

Next up, vertical tracking alignment, or VTA. This final alignment refers to the whole tone arm level across the record surface. You want the tone arm distance from the record to sit evenly from front to back. That is, the front (cartridge end) should not sit lower than the back (pivot end), and vice versa. Some turntables will allow you to correct uneven VTA by raising or lowering the tonearm at the pivot end. If your turntable does not feature such an adjustment, you can use a combination of cartridge washers, and placemats to adjust your tonearm height from the cartridge end.

Levelling the Turntable

Last but not least is turntable level. Once you’ve finished setting up a turntable, it is imperative you place it on an even surface – failing to do so could through off your carefully aligned deck and ultimately void the entire process. Start with a solid, even surface and use a spirit level to help you measure any fine adjustments.

To help you get to grips with the adjustments I’ve described, I recommend also watching the following YouTube video:

The Bottom Line

I love vinyl records, but I’m under no illusion when it comes to the compromises. On paper, digital is superior in almost every way from a technical standpoint. However, specifications can also be deceiving, and current mastering practices often lead to vinyl releases having greater dynamic range than their digital counterparts, which is ironic.

For me, digital is very convenient, but it’s also clinical – both from an audible and tangible perspective. I listen to analog and digital formats, but there’s just something extra special about vinyl – warts and all. End-of-side distortion is arguably one of the peskiest drawbacks, but you can reduce it by carefully configuring your setup. Do so, and your records will reward you with beautiful sound for many years to come.

Author

  • Marc Henshall

    Marc is the owner of Sound Matters and a musician with a BSc Honours Degree in Music Technology. His love for records grew in the fallout from digital downloads and a feeling that, somehow, without the physical medium, the magic was lost.

Subscribe
Notify of
guest

20 Comments
Newest
Oldest Most Voted
Inline Feedbacks
View all comments
Rusty White

Albums that were originally compiled onto only 1 vinyl record seem to be reproduced these days on 2 records in the album. Are they doing this so that they can keep from getting too close to the center, thus avoiding this distortion effect?

Plarocks

That, and to be able to cut the record hotter.

Also, the 30 minute side was possible with the 80s DMM mastering, but that method has kinda been put by the wayside for more traditional lacquer cuttings.

STERCKEMAN

I’ve got a Technics SL 1200 MK2 and even changing my Ortofon OM Gold for a Ortophon 2M Black the distortions are still audible at the end of my records.

Vinylisterner

And these distortions will be present forever. With the better (sharper) stylus they will be just less audible.That’s it ,there’s no any way to eliminate them to the end.

john fraser

Please go to analog magik online and watch set up tutorials to see what”s involved to get optimum play back of a vinyl record.In the words of doug stax the easiest thing to play incorrectly is a vinyl record.I am not selling anything just knowledge

[…] no such thing a perfect format, and I’ll be the first to recognize that vinyl has its faults (end-of-side distortion, for example), but there’s no mistaking just how great vinyl sounds when it’s made right. Vinyl is a […]

[…] have particular benefits when considering inner-groove distortion, as the natural high-frequency roll-off that happens as the groove progresses toward the record center is greatly […]

[…] Vinyl Record Inner-Groove Distortion (A Simple Explanation)https://www.yoursoundmatters.com/vinyl-record-inner-groove-distortion-simple-explanation/ […]

[…] Vinyl Record Inner-Groove Distortion (A Simple Explanation)https://www.yoursoundmatters.com/vinyl-record-inner-groove-distortion-simple-explanation/ […]

[…] also decline in sound quality towards the end of each side; this is because of an issue called ‘inner-groove distortion.’ Personally, I can’t stand listening to it, but some people don’t care because it’s just […]

T The One

Is it true that a linear tracking turntable will reduce the inner groove distortion? i have a technics SL-7 with an Audio Technica AT-81cP cartrigde and in my opinion it’s less than with the cartrigde it originaly came with (P202C). however idk if it’s less than if i had just used a regular turntable. can anyone confirm this?

Vinylisterner

just a little bit better on linears but IGD still is present.

Robert Bosson

Inner groove distortion is an ugly hysteria promulgated by vinyl snobs. Yes, the inner groove places more demands on the format, however the truth is if set up your TT and cart to be geometrically perfect, and if the quality of the pressing allows, there is absolutely no excuse not to get faithful, undistorted vinyl reproduction across the whole record.

DanJohnson

Total B.S. Your “opinion” does not trump the laws of physics and the obvious reasons for why the signal is degraded (especially in the mid range). The linear regression alone is bad enough but then you add in the signal compression and the inner track of ANY record pressed to the 20 minute mark will sound bad. The latest pressings by artists who care, use about 14 minutes per side on 180 Gm vinyl . Best youre going to get

robinlandseadel

LPs, as of 2019, are moronic. Distortion is distortion and it’s baked into the equation. Why not develop a “euphonic” distortion generator? Wasteful, self distructing, more about collection/hoarding than music. Just hang it up.

blake kersey

I can’t believe you didn’t mention the REAL remedy to “end of side distortion”! It’s really due to the larger profile of conical and elliptical styli. If you really want to get rid of the tracing error, then get a fine line or shibata stylus cart. For example I have a Ortofon Concorde cart with an om30 fine line stylus. The narrower profile of the stylus damn near obliterates the end of side distortion.

Dale Cosby

Where can you order those? And are they expensive? One thing I am trying tonight, I record my LPs to my computer to put on my iPod so I tried recording it at 45rpm. I will then convert it once it is on the computer. But I am interested to see the difference. My stylus probably needs to be replaced. The date says 10-2015 on it. I normally like to put a new one on each year but I don’t know how often I should.

blake kersey

I know it’s been almost a year, my sincerest apologies. Theres a guy on Ebay that sells the 10-40 styli with the 40 being $289 and the prices going downward from there. His name is something like William Thakker. He sells them for cheaper than you would find elsewhere. I’ve moved on to the more expensive VM760SLC which was $649. This thing is absolutely wonderful and worth the high price. Study the different styli, and you can make a decision based on what you find.

[…] at the grooves closest to the end of each side on a record. (Check out our previous post on inner-groove distortion and cartridge alignment for more on this […]